Home | KSAE | E-Submission | Sitemap | Contact Us |  
top_img
Previous issue > Previous issue



Table of Contents | September, 2004  Vol. 5   No.3 Previous Issue | Next Issue | Archive
Articles
 Heat Transfer, Fluid and Thermal Engineering
145 A PARAMETRIC SENSITIVITY STUDY OF GDI SPRAY CHARACTERISTICS USING A 3-D TRANSIENT MODEL
P. J. BOWEN, M. A. COMER, S. M. SAPSFORD, S. I. KWON
aaa Int J Automot Technol. 2004;5(3):145-153.
      
 
155 CHARACTERISTICS OF WALL IMPINGEMENT AT ELEVATED TEMPERATURE CONDITIONS ON GDI SPRAY
K. S. IM, J. PARK, H. KIM, M. C. LAI
aaa Int J Automot Technol. 2004;5(3):155-164.
      
 Engine, Emission Technology
165 MODELING OF DIRECT INJECTION DIESEL ENGINE EMISSIONS FOR A QUASI-DIMENSIONAL MULTI-ZONE SPRAY MODEL
D. JUNG, D. N. ASSANIS
aaa Int J Automot Technol. 2004;5(3):165-172.
      
 Automobile Body and Safety
173 CRASHWORTHY DESIGN AND EVALUATION ON THE FRONT-END STRUCTURE OF KOREAN HIGH SPEED TRAIN
J.-S. KOO, Y. H. YOUN
aaa Int J Automot Technol. 2004;5(3):173-180.
      
 Alternative Energy & Vehicle
181 COMBUSTION CHARACTERISTICS OF INHOMOGENEOUS METHANE-AIR MIXTURE IN A CONSTANT VOLUME COMBUSTION CHAMBER
C. H. JEON, S. H. CHOI, Y. J. CHANG
aaa Int J Automot Technol. 2004;5(3):181-188.
      
 Materials and Recycling, Manufacturing
189 OPTIMAL DESIGN OF THE MULTIPLAYER DAMPING MATERIALS USING EQUIVALENT MODELING
D. J. HUR, D. C. LEE
aaa Int J Automot Technol. 2004;5(3):189-194.
      
 Engine, Emission Technology
195 EXPERIMENTAL STUDY ON HOMOGENEOUS CHARGE COMPRESSION IGNITION ENGINE OPERATION WITH EXHAUST GAS RECIRCULATION
S. B. HAN, G. H. CHOI, R. W. DIBBLE
aaa Int J Automot Technol. 2004;5(3):195-200.
      
 Fuel Cell, Hybrid and Electrical Vehicle
201 HARDWARE IN THE LOOP SIMULATION OF HYBRID VEHICLE FOR OPTIMAL ENGINE OPERATION BY CVT RATIO CONTROL
H. S. KIM, H. YEO, C. H. SONG, C. S. KIM
aaa Int J Automot Technol. 2004;5(3):201-208.
      
 Automobile Chassis & Vehicle Dynamic
209 NOISE REDUCTION OF AN ENCLOSED CAVITY BY MEANS OF AIR-GAP SYSTEMS
S. W. KANG, J. M. LEE
aaa Int J Automot Technol. 2004;5(3):209-213.
      
 Materials and Recycling, Manufacturing
215 ESTIMATION OF FATIGUE LIFE BY LETHARGY COEFFICIENT USING MOLECULAR DYNAMIC SIMULATION
S. M. YANG, J. H. SONG, H. G. NOH, H. S. YU, H. Y. KANG
aaa Int J Automot Technol. 2004;5(3):215-219.
      
Editorial Office
21 Teheran-ro 52-gil, Gangnam-gu, Seoul 06212, Korea
TEL: +82-2-564-3971/2   FAX: +82-2-564-3973   E-mail: car@ksae.org
About |  Browse Articles |  Current Issue |  For Authors and Reviewers
Copyright © The Korean Society of Automotive Engineers. All rights reserved.                 Developed in M2community
Close layer
prev next